Hertz 4-Speaker and Amplifier System 2014-2023 Street Glide

SP 4.500 features Hertz ADC (Advanced D-Class) output stage, reaching up to 87% efficiency and delivering an impressive power rating of 90 x 4 (4Ω) W RMS or 300 W x 2 (4Ω) W RMS when bridged, with an ultra-compact size of 192.7 (7.58) x 130 (5.1) mm (in.) x 49 (1.9). Being ultra-compact with impressive power, SP 4.500 is the ideal choice for Motorcycle applications

Features:

• Up to 87% efficiency thanks to ADC (Advanced D-Class) output stage.
• USS (Universal Speakers Simulators) allows SP 4.500 to work with head units featuring the “speaker load detection” circuit.
• 90 W RMS x 4 (4Ω) with ultra-compact size: 192.7 x 130 x 49 / 7.59 x 5.12 x 1.93 (mm/inch)
• IP55 aluminum chassis for maximum protection against humidity and external agents.
• No cooling fan to prevent internal accumulation of dirt.
• Sealed power cord, line inputs and speaker outputs to prevent oxidation.
• Crossover filters and controls on a single side to facilitate calibration when the product is installed.
• Balanced fully-differential high-noise rejection inputs.
• ART (Automatic Remote Turn-On/Off) automatically turns on/off the amplifier when the OEM head-unit turns on/off (can be enabled/disabled).

Specs:

Channels    4 - 3 - 2
Nominal power supply voltage    11 ÷ 15 VDC
Pulse Operating voltage    6 ÷ 16 VDC
Idling current    1.1 A
Idling current when off    0.03 mA
Consumption @ 14.4 VDC, MIN load impedance (Max Musical Power)    50 A
Remote IN    6 ÷ 15 VDC (9 mA)
DC-REM - Remote Turn on by SPK DC from OUTPUT BTL speakers    3.5 ÷ 7 VDC
Distortion - THD @ 1 kHz, 4Ω, 70% Rated Power    0.02%
Damping factor @ 1 kHz, 4Ω, 2 VRMS    200
Bandwidth @ -3 dB    10 Hz ÷35 kHz
S/N ratio (A weighted @ 1 V Input)    105 dBA
Pre-In sensitivity    0.6 ÷ 6 VRMS
Speaker-In sensitivity    2.2 ÷ 22 VRMS
Minimum load impedance:    
@ 4Ch    2Ω
@ 3Ch    2Ω + 2Ω + 4Ω
@ 2Ch    4Ω
IP Rating    IP55
Operating Temperature Range    0°C (32°F) to 55°C (131°F)
Max size (mm/inch)    211.6 x 130 x 49 / 8.33 x 5.118 x 1.929
Weight (kg/lbs)    2.15 / 4.74
Adjustable Crossovers    yes

Inputs/Filters:

INPUTS:Pre IN / Speaker IN
Ch 1-2
FullYes
Hi-pass: 50 ÷ 5k Hz @ 12 dB/Oct.
Lo-pass: 50 ÷ 5k Hz @ 12 dB/Oct.
Ch 3-4
FullYes
Hi-pass: 50 ÷ 5k Hz @ 12 dB/Oct.
Lo-pass: 50 ÷ 5k Hz @ 12 dB/Oct.
Bass Boost: 45Hz (adjustable)OUT 3 - 4 (0 ÷ 8) dB [LP = ON only]

Output Power:

Output Nominal Power (RMS) @ 14.4 VDC, THD 1%:
4 Ch: 90 W x 4 (4Ω)
4 Ch: 150 W x 4 (2Ω)
3 Ch: 80 W x 2 (4Ω) + 330 W x 1 (4Ω)
3 Ch: 145 W x 2 (2Ω) + 300 W x 1 (4Ω)
2 Ch: 300 W x 2 (4Ω)
Total: 600 W

*** Upgrade to the SP4.900 ***

SP 4.900 is the first Hertz amplifier featuring the renewed Hertz ADC (Advanced D-Class) output stage, reaching up to 85% efficiency and delivering an impressive power rating of 160 x 4 (4Ω) W RMS or 500 W x 2 (4Ω) W RMS when bridged, with an ultra-compact size of 211.6 (8.3) x 130 (5.1) mm (in.). Being ultra-compact with impressive power, SP 4.900 is the ideal choice for Harley applications.

Features:

• Up to 87% efficiency thanks to ADC (Advanced D-Class) output stage.
• USS (Universal Speakers Simulators) allows SP 4.900 to work with head units featuring the “speaker load detection” circuit.
• 160 W RMS x 4 (4Ω) with ultra-compact size 211.6 x 130 x 49 / 8.3 x 5.1 x 1.9 (mm/inch).
• IP55 aluminium chassis for maximum protection against humidity and external agents.
• No cooling fan to prevent internal accumulation of dirt 6. Sealed power cord, line inputs, and speaker outputs to prevent oxidation.
• Crossovers filters and controls on a single side to facilitate calibration when the product is installed.

Specs:

Channels    4 - 3 - 2
Nominal power supply voltage    11 ÷ 15 VDC
Pulse Operating voltage    6 ÷ 16 VDC
Idling current    1.1 A
Idling current when off    0.03 mA
Consumption @ 14.4 VDC, MIN load impedance (Max Musical Power)    50 A
Remote IN    6 ÷ 15 VDC (9 mA)
DC-REM - Remote Turn on by SPK DC from OUTPUT BTL speakers    3.5 ÷ 7 VDC
Distortion - THD @ 1 kHz, 4Ω, 70% Rated Power    0.02%
Damping factor @ 1 kHz, 4Ω, 2 VRMS    200
Bandwidth @ -3 dB    10 Hz ÷35 kHz
S/N ratio (A weighted @ 1 V Input)    105 dBA
Pre-In sensitivity    0.6 ÷ 6 VRMS
Speaker-In sensitivity    2.2 ÷ 22 VRMS
Minimum load impedance:    
@ 4Ch    2Ω
@ 3Ch    2Ω + 2Ω + 4Ω
@ 2Ch    4Ω
IP Rating    IP55
Operating Temperature Range    0°C (32°F) to 55°C (131°F)
Max size (mm/inch)    211.6 x 130 x 49 / 8.33 x 5.118 x 1.929
Weight (kg/lbs)    2.15 / 4.74
Adjustable Crossovers    yes
Output Power:

Output Nominal Power (RMS) @ 14.4 VDC, THD 1%:    
4 Ch:    160 W x 4 (4Ω)
4 Ch:    250 W x 4 (2Ω)
3 Ch:    160 W x 2 (4Ω) + 500 W x 1 (4Ω)
3 Ch:    250 W x 2 (2Ω) + 500 W x 1 (4Ω)
2 Ch:    500 W x 2 (4Ω)
Total Power    1000 W

INPUTS / FILTERS:

INPUTS:    Pre IN / Speaker IN
Ch 1-2    
Full    -
Hi-pass    50 ÷ 5k Hz @ 12 dB/Oct.
Lo-pass:    50 ÷ 5k Hz @ 12 dB/Oct.
Ch 3-4    
Full    -
Hi-pass    50 ÷ 5k Hz @ 12 dB/Oct.
Lo-pass    50 ÷ 5k Hz @ 12 dB/Oct.
Bass Boost 45Hz (adjustable)    (0 ÷ 8) dB [LP = ON only]

This is a truly amazing Harley-specific speaker. Hertz hit it out of the park with this design. The large oversized 1.4-inch tweeter is the loudest non-horn tweeter we have ever tested and it is louder and better sounding than many stand-alone horns. The woofer of this speaker is a pro audio design that has been optimized for use in Harley applications. Designed to perform in the fairing, tour packs, and lower fairings these woofers deliver clarity and loudness for even the largest scale systems.

Features:

1. Nature-proof high stiffness pressed-paper cone featuring innovative water/ humidity resistant and anti-UV treatments.

2. Durable Extreme SPL performance in a compact size & light-weight thanks to the N38 H Neodymium grade magnet.

3. Unparalleled power handling delivered by the double layer copper voice coil, wound on polyamide former.

4. Hi-SPL 1.4” Neodymium magnet PEI dome tweeter with resettable solid-state tweeter protection circuit.

5. Double faston terminals allow daisy-chaining of multiple units and provide compatibility with most common motorcycle connections.

Specs:

Component    SPL COAXIAL
Size mm (in.)    165 (6.5)
Power Handling - Continuous W    100
Power Handling - Peak W    200
Impedance Ohm    4
Tweeter diaphragm mm (in.)    PEI
Woofer Voice Coil Ø mm (in.)    38 (1.5)
Tweeter Voice Coil Ø mm (in.)    28 (1.1)
Frequency Response Hz    100 ÷ 20k
Woofer Magnet size D x d x h mm (in.)    70 x 45 x 7 (2.76 x 1.77 x 0.28)
Tweeter Magnet size D x h mm (in.)    19 x 3 (0.75 x 0.12)
Weight of one speaker kg (lb.)    0,94 (2.08)
Woofer Magnet    Special Neodymium N38 H
Tweeter Magnet    Special Neodymium N38 H
Cone    Water repellent pressed paper

Electro-acoustic Specs:

D mm    128
Re Ohm    3,3
Fs Hz    110
Le mH    0,061
Vas I    4,92
Mms g    10,14
Cms mm/N    0,21
BL T*m    5,83
Qts    0,64
Qes    0,68
Qms    9,7
Spl dB    96,5

SX 690.1 NEO is a real beast with a Hi-SPL Mid-Hi unit based on a 1.4” dome tweeter and 1” dome super tweeter with a resettable solid-state protection circuit. Cone is made with nature-proof high stiffness pressed paper featuring innovative water/humidity resistance and anti-UV treatments. The double-layer copper voice coil wound on polyimide former ensures unparalleled power handling. New motors units are made of special Neodymium N38 H to obtain a minimum bulk and increased performance.

Features:

1. Nature-proof high stiffness pressed-paper cone featuring innovative water/ humidity resistant and anti-UV treatments.

2. Durable Extreme SPL performance in a compact size & light-weight thanks to the N38 H Neodymium grade magnet.

3. Unparalleled power handling delivered by the double-layer copper voice coil, wound on polyimide former.

4. Hi-SPL Mid-Hi unit based on 1.4” dome tweeter and 1” dome super tweeter with resettable solid-state tweeter protection circuit.

5. Double faston terminals allow daisy-chaining of multiple units and provide compatibility with the most common motorcycle connections.

Specs:

Component    SPL COAXIAL
Size mm (in.)    in. 6 x 9
Power Handling - Continuous W    130
Power Handling - Peak W    260
Impedance Ohm    4
Tweeter diaphragm mm (in.)    29 (1.14)
Woofer Voice Coil Ø mm (in.)    38 (1.5)
Tweeter Voice Coil Ø mm (in.)    25 (1)
Frequency Response Hz    65 ÷ 24k
Woofer Magnet size D x d x h mm (in.)    110 x 45 x 20 (4.33 x 1.77 x 0.79)
Tweeter Magnet size D x h mm (in.)    24,5 x 6 x 3,5 (0.96 x 0.24 x 0.14)
Weight of one speaker kg (lb.)    1,69 (3.73)
Woofer Magnet    Special Neodymium N38 H
Tweeter Magnet    Special Neodymium N38 H
Cone    Water repellent pressed paper
Dome    Tetolon

Electro-acoustic Specs:

D mm    169
Xmax mm    5,5
Re Ohm    3
Fs Hz    65
Le mH    0,4
Vas I    11,29
Mms g    36,1
Cms mm/N    0,16
BL T*m    7,665
Qts    0,62
Qes    0,78
Qms    2,9
Spl dB    94

This Is The Part You Need! Adding An Amplifier To Your 2014 Or Newer Harley Davidson Touring Bike Has Never Been Easier.

True Plug & Play! This is the very best way to integrate an aftermarket amplifier with the factory radio of any '14 or newer Harley bagger. This harness gives you all of the connections and features you could want and it works with all variations of Harley stereo systems from basic to CVO Ultra models, both factory-amplified and non-amplified.

This Part Replaces All of the Following Harnesses. Which makes it the best deal, and the cleanest and easiest way to go:

• 2014-Up Harley Plug & Play Signal Adapter 14FPNP
• 2014-Up Harley Plug & Play Rear Signal Adapter
• Stealth Accessory Harness Power Tap
• Rear Harley Speaker Wire Harness for Bags or Tour Pack
• Stealth Power Tap Harness for Battery & Ground
• Ultra Rear Radio Signal & Speaker T Harness
• Harley Speaker Pod Plug Adapters for Fairing Speakers

Fitment: 2014 and up Road Glide, Street Glide, Electra Glide, Ultra, CVO, and all amplified and non amplified variations. Amplifier bypass plugs required for all factory amplified systems.?Amplifier bypass plugs are available. Balanced speaker level on RCA, requires an amplifier or DSP that is designed to accept speaker level in on RCA connection (most all quality amplifiers and DSPs do accept speaker level, but check your equipment to make sure). CVO and bikes that only have fairing speakers will require a radio flash to enable the rear RCA output. You can flash your own bike with a separate single bike flash tool.

Does Not Work With Sound Digital Or Dayton Amplifiers (there may be others we're not aware of though)

• True Plug & Play! No cutting any factory wires.
• Both front and rear (4 Channel) RCA out from factory radio (balanced speaker level on RCA, requires an amplifier or DSP that is designed to accept speaker level input on RCA connection).
• Front and rear speaker connections for factory locations.
• Built-in load resistors keep factory radio happy and eliminate distortion.
• Accessory, battery, and ground outputs for powering DSP without the need for any additional parts or plugs.
• Wire ferrules and crimp connectors built into the harness. No extra connectors needed.
• 100% developed and designed by American Hard Bag in the USA.

This power amplifier kit comes complete with all the cabling, speaker wires, terminals, disconnects, and waterproof fuse holder needed to perform a quality installation for a typical amplifier, except for RCA interconnects.

What We Like About This Kit:
It has a waterproof eight gauge fuse holder that uses mini ANL-style fuses for superior current transfer and reliability. Furthermore, the fuse holder is compact and very friendly to mount. All of the wire runs are blacked-out with a nice-looking braided loom and heat-shrunk at each end.

Are you looking to add 6x9's to your stock lids? Don't want to spend the big bucks and buy color matched CVO lids from the dealer? Yet you don't want to chinch out and buy crummy aftermarket lids. The Hertz HD14H saddle bag lid cut-in kit makes it possible for you to add their 6x9 speakers to your stock, non-speaker lids you currently have without sacrificing quality, safety and without emptying your wallet.

Will only work on stock, non-CVO lids, without electric lid lock motor, on 2014+ lids.

DON’T SETTLE FOR 5X7S WHEN YOU CAN HAVE 6X9S IN YOUR FACTORY HARLEY SPEAKER LIDS!

This kit requires modification of your factory speaker lids. The integrated plastic basket on the underside of the speaker lid must be cut off and ground down to create a flat mounting surface for the adapter to mount on. This is done quickly and easily with an oscillating cutting tool, or a Roloc disc on a die grinder.

This kit includes (8) eight aluminum threaded nutserts. A nutsert tool with an 8-32 insert is required to complete the installation. If you do not have a nutsert tool, one can be found locally, check with your nearest Hardware store or tool company. 

Update!: This kit will now work with CVO electronic lid lock mechanisms, but you must select the optional lid lock adapter above before adding it to the cart.

The ultra-compact S8 DSP is the perfect solution for integrating any OEM source into your audio upgrade project for cars, motorcycles, and boats! S8 DSP is a distilled essence of technology at the service of the highest audio quality in a corrosion-free case cast in metal and composite materials.

S8 DSP processes the audio signal with 96 kHz / 24-bit resolution and has obtained the Hi-Res certification from the JAS (Japan Audio Society), an acknowledgment that certifies the extreme level of audio performance achieved.

The powerful 32-bit DSP manages 6 high/low-level analog input channels, one digital coaxial input, and 8 output channels, offering maximum freedom of configuration to the specialist. The SPDIF coaxial input is ideal for digital connection with a Hi-Res player, a solution that allows for maximum listening quality. For each of the eight output channels we have a level control, the 15-pole parametric equalizer, time delays, and crossover filter available. The 7-band parametric equalizer of the input signal allows obtaining a flat response from OEM sources, which often have an exaggerated emphasis on the low frequency.

Features:

1. Small and weatherproof – perfect for motorcycles

• Compact size featuring all connections on one side to be installed anywhere

• Anti-corrosion-treated PCB to ensure years of listening pleasure in open nature

• Three different application setups: Car, Motorcycle, Free placement (boat, van, pick-up)

• Party & Ride presets, to optimize the sound performance in all conditions

2. Configurable with a PC, a Mac, an Android device, or an iOS device

• IOS/Android control APPs (Bluetooth 5.0)

• DRC control over app from iOS/Android devices

3. Powerful DSP with the excellent sound quality you expect from Hertz

• Hi-Res audio (96 kHz/24-bit native resolution) for unparalleled audio quality

• 6-channel SPEAKER IN (2,5 – 21 Vrms) on a dedicated socket with a built-in USS

(Universal Speakers Simulator)

• SPDIF coaxial input (up to 24bit/96KHz)

• 8-channel / 4Vrms-capable RCA outputs

• Signal Output Active Limiter prevents clipping

Specs:

Nominal Power supply voltage / fuse:    7 ÷ 20 VDC / 1A
Pulse operating voltage:    5 ÷ 24 VDC
Idling current:    0.34 A
OFF current (ART= OFF):    <80 uA
OFF current (ART= ON):    <80 uA
Remote IN    6 ÷ 20 VDC (10 mA)
Remote OUT    4 ÷ 20 VDC (150 mA)
ART - Automatic Remote Turn on/off from BTL speaker outputs (selectable):    1.5 ÷ 7 VDC

Output Stage:
Analog outputs (rca)    8 channels
Max output level (rms) @ 0.05% THD    4V
Analog outputs management    The DSP controls each output channel: gain, crossover, EQ, delay, polarity
Bandwidth    10Hz – 40KHz (+/-3db)
Signal to noise ratio (A weighted)    105dBA (Analog Input) 112dBA (Digital Input)
THD+N (@ 1Vrms out, @ 1Khz)    <0.005%
Crosstalk (channel separation) @ 1KHz    >95dBA

Input Stage:
Analog low level Inputs    6 ch. (Differential input) (Molex microfit to RCAs)
Analog high level Inputs    6 ch. (Differential input) (Molex microfit to tripped ends) + USS (Universal Speakers Simulator)
Digital inputs    Yes (Coaxial SPDIF; up to 24bit 96KHz) (Molex microfit to RCA)
Input sensitivity (low level)    0.8V – 6V RMS
Input sensitivity (high level)    2.5V – 21V RMS
Analog inputs management    Audio input routing matrix type
Analog inputs eq    7 bands paragraphic for each input channel
ART    Automatic Remote Turn-On/Off with Speaker-In

Digital Signal Processor:
Sample rate    96KHz
Bit depth    24
Output equalizer    15 bands per channel w/ adjustable Q and Frequency
Equalizer resolution    1/10th dB per step +12dB / -12dB
Time alignment (distance)    0 ÷ 468.4 cm / 0 ÷ 184.4 inches
Time alignment (time)    0 ÷ 13.5ms
Time alignment (step)    0,08 ms; 2,8 cm / 1.1 inch
Time alignment (fine set)    0,02 ms; 0,7 cm / 0.27 inch
Crossovers    AP/HP/LP/BP all channels
Crossover type    Butterworth, Linkwitz-Riley, Bessel (All Channels)
Crossover slope    From 6dB/oct. until 30dB/oct. (6dB step)
Crossover steps    120 steps 20Hz-20KHz
Mute function    Each channel individually, or all channels.
Presets    4 presets
Presets selection    2 specific wires to control the 4 presets selection by extarnal switches.
Input selection by wire    One specific wire to select the desired input between Analog or Digital.
Audio signal compressor on output stage    Yes (enable/disable)
DSP chipset    Analog Device: ADAU1451
DSP management by bt app (iOS/ Android) :  

1. CONFIGURATOR mode Mainly it’ll allow the DSP tuning. You can manage every DSP functon through your smartphone/ tablet/PC/MAC.

2. DRC mode The BT device becomes a remote control by using the dedicated app with a simple graphical user interface. Manage volume level, SUB level, select different setup files, upload a new setup file.
Setup file sharing via bt    Upload a setup file via BT through the BT APP when in “Configurator” or “DRC” mode.
DSP management by pc / mac / ios / android    Microsoft Windows (32/64 bit): Windows 10 (USB and BT BLE) Windows 11 (USB and BT BLE) Mac Os: 10.13 Hight Sierra or later (USB and BT BLE)

Physical Specs:
Max size W x H x D (mm/inch)    130 x 33.8 x 88,3 / 5.11 x 1.44 x 3.47
Weight (kg/lbs)    0,66 / 1.45