Velocity High-Power Horn Speaker Packag for 2014-2023 Street Glide

The RZA1000.4 is the very best-sounding amplifier made specifically for Harley use. This amplifier has better speaker cone control at high volumes for better bass, and far better high frequency fidelity than other amplifiers. Natively compatible with factory Harley radios and aftermarket radios alike, the RZA1000.4 has a super wide range input (.41 to 10 volts) that is balanced so that it can accept anything from a standard line level RCA to a high voltage speaker level input directly from a factory radio. And it does this without the need for any noisy line levelers. This amplifier uses a far superior internal power supply to other amplifiers and can sustain extreme performance where other amplifiers just run out of gas and clip or drop in volume. This is a beast of an amplifier in a small footprint. This amplifier features a full chassis heat sink for more performance in a much smaller size package. The full chassis heat sink also allows for the amplifier to be mounted in any position and to keep cool even on the hottest summer days.

FEATURES:
Full Chassis Heat Sink Design Can Be Mounted in Any Position

• Compact Design Fits All ‘14 and Later Fairings Without Any Modification
• Super Wide Range Signal Input Stage Is Compatible With Most Any Type of Analog Signal
• Made Specifically for Harley Applications
• Optimized for Velocity Speakers
• Flexible Design Is Perfect for Every Type of Speaker on a Bike Including Subwoofers, Bag Woofers, Mid Ranges, and Tweeters
• Onboard Active 12 db crossovers

Specifications:

• 1,350 Watts Peak Power

• 4 x 275 Watts @ 2 Ohm RMS

• 4 x 150 Watts @ 4 Ohm RMS

• 2 x 550 Watts @ 4 Ohm RMS

• Frequency Response 20hz - 25khz

• Crossover High/Low Pass 40hz - 400hz @ 12db

• Signal Input Range .41V - 10V Balanced High & Low Level

• RCA Input - Yes

• Speaker Level Input - Yes (over RCA connection)

• Efficiency 87% @ Full Power

• Remote Trigger 12V or Signal Sense

The Velocity RZ65H speakers are a huge jump forward in tunability for pro-audio-type speakers on Harley baggers. We built the RZ65H speakers to sound better out of the box without the typical response issues of horn-loaded pro-audio-type speakers.

These speakers are the best of both worlds
Ultra-high output, and smooth frequency response. Very high efficiency means that you get more output for every watt. 

Specs:

Impedance 4 Ohms

RE 3.188 Ohms

FS 92 Hz

QMS 6.711

QES .3947

QTS .3727

Sens 101 db

RMS 300W (pair) Max 600W (pair)

The RZ69H coax horn is a true woofer and tweeter component set mounted on a common frame. The electrical connections for the horn and the woofer are discrete. The RZ69H speaker has two sets of connection terminals. The spring-loaded terminals attached to the speaker frame are for the 6x9” woofer and the spade terminals on the rear of the magnet are for the horn tweeter. The included passive crossover must be connected between the horn and the amplifier. The woofer should be connected directly to the amplifier and does not require any filter from a passive crossover. Both the horn and the woofer should be connected in parallel to the same amplifier channel as shown in the illustration. The easy way to do this is to simply connect the passive crossover input connections to the woofer terminals along with the amplifier connections. This puts the horn tweeter in parallel with the woofer.

Specs:

Impedance 4 Ohms

RE 3.273 Ohms

FS 75 Hz

QMS 7.111

QES .7555

QTS .683

Sens 101 db

RMS 300W (pair) Max 600W (pair)

This Is The Part You Need! Adding An Amplifier To Your 2014 Or Newer Harley Davidson Touring Bike Has Never Been Easier.

True Plug & Play! This is the very best way to integrate an aftermarket amplifier with the factory radio of any '14 or newer Harley bagger. This harness gives you all of the connections and features you could want and it works with all variations of Harley stereo systems from basic to CVO Ultra models, both factory-amplified and non-amplified.

This Part Replaces All of the Following Harnesses. Which makes it the best deal, and the cleanest and easiest way to go:

• 2014-Up Harley Plug & Play Signal Adapter 14FPNP
• 2014-Up Harley Plug & Play Rear Signal Adapter
• Stealth Accessory Harness Power Tap
• Rear Harley Speaker Wire Harness for Bags or Tour Pack
• Stealth Power Tap Harness for Battery & Ground
• Ultra Rear Radio Signal & Speaker T Harness
• Harley Speaker Pod Plug Adapters for Fairing Speakers

Fitment: 2014 and up Road Glide, Street Glide, Electra Glide, Ultra, CVO, and all amplified and non amplified variations. Amplifier bypass plugs required for all factory amplified systems.?Amplifier bypass plugs are available. Balanced speaker level on RCA, requires an amplifier or DSP that is designed to accept speaker level in on RCA connection (most all quality amplifiers and DSPs do accept speaker level, but check your equipment to make sure). CVO and bikes that only have fairing speakers will require a radio flash to enable the rear RCA output. You can flash your own bike with a separate single bike flash tool.

• True Plug & Play! No cutting any factory wires.
• Both front and rear (4 Channel) RCA out from factory radio (balanced speaker level on RCA, requires an amplifier or DSP that is designed to accept speaker level input on RCA connection).
• Front and rear speaker connections for factory locations.
• Built-in load resistors keep factory radio happy and eliminate distortion.
• Accessory, battery, and ground outputs for powering DSP without the need for any additional parts or plugs.
• Wire ferrules and crimp connectors built into the harness. No extra connectors needed.
• 100% developed and designed by American Hard Bag in the USA.

This power amplifier kit comes complete with all the cabling, speaker wires, terminals, disconnects, and waterproof fuse holder needed to perform a quality installation for a typical amplifier, except for RCA interconnects.

What We Like About This Kit:
It has a waterproof eight gauge fuse holder that uses mini ANL-style fuses for superior current transfer and reliability. Furthermore, the fuse holder is compact and very friendly to mount. All of the wire runs are blacked-out with a nice-looking braided loom and heat-shrunk at each end.

Perfect For Adding Speakers to Saddlebags! This plug & play three-piece harness adds speaker wire that runs from the bike's front fairing to each saddlebag. The kit comes complete with stainless wire inlets that keep water out and clamp the cable in place. Each saddlebag input section of the harness has waterproof quick disconnects rated for more than 500 watts of insane amplifier power on each pin!

The deluxe version comes with a service disconnect at the lid and a 4 pin Molex connector on the amplifier end that is directly plug and play with Harley radios as well as all American Hard Bag, Musway, and Velocity amplifier 4 pin disconnects. These small changes require quite a few additional components and sections to be added to the wire harness assembly but the end result is a slam dunk of an install and a much more serviceable audio system overall.

The ultra-compact S8 DSP is the perfect solution for integrating any OEM source into your audio upgrade project for cars, motorcycles, and boats! S8 DSP is a distilled essence of technology at the service of the highest audio quality in a corrosion-free case cast in metal and composite materials.

S8 DSP processes the audio signal with 96 kHz / 24-bit resolution and has obtained the Hi-Res certification from the JAS (Japan Audio Society), an acknowledgment that certifies the extreme level of audio performance achieved.

The powerful 32-bit DSP manages 6 high/low-level analog input channels, one digital coaxial input, and 8 output channels, offering maximum freedom of configuration to the specialist. The SPDIF coaxial input is ideal for digital connection with a Hi-Res player, a solution that allows for maximum listening quality. For each of the eight output channels we have a level control, the 15-pole parametric equalizer, time delays, and crossover filter available. The 7-band parametric equalizer of the input signal allows obtaining a flat response from OEM sources, which often have an exaggerated emphasis on the low frequency.

Feature:

1. Small and weatherproof – perfect for motorcycles

• Compact size featuring all connections on one side to be installed anywhere

• Anti-corrosion-treated PCB to ensure years of listening pleasure in open nature

• Three different application setups: Car, Motorcycle, Free placement (boat, van, pick-up)

• Party & Ride presets, to optimize the sound performance in all conditions

2. Configurable with a PC, a Mac, an Android device, or an iOS device

• IOS/Android control APPs (Bluetooth 5.0)

• DRC control over app from iOS/Android devices

3. Powerful DSP with the excellent sound quality you expect from Hertz

• Hi-Res audio (96 kHz/24-bit native resolution) for unparalleled audio quality

• 6-channel SPEAKER IN (2,5 – 21 Vrms) on a dedicated socket with a built-in USS

(Universal Speakers Simulator)

• SPDIF coaxial input (up to 24bit/96KHz)

• 8-channel / 4Vrms-capable RCA outputs

• Signal Output Active Limiter prevents clipping

Specs:

General Specifications:
Nominal Power supply voltage / fuse:    7 ÷ 20 VDC / 1A
Pulse operating voltage:    5 ÷ 24 VDC
Idling current:    0.34 A
OFF current (ART= OFF):    <80 uA
OFF current (ART= ON):    <80 uA
Remote IN    6 ÷ 20 VDC (10 mA)
Remote OUT    4 ÷ 20 VDC (150 mA)
ART - Automatic Remote Turn on/off from BTL speaker outputs (selectable):    1.5 ÷ 7 VDC

Output Stage:
Analog outputs (rca)    8 channels
Max output level (rms) @ 0.05% THD    4V
Analog outputs management    The DSP controls each output channel: gain, crossover, EQ, delay, polarity
Bandwidth    10Hz – 40KHz (+/-3db)
Signal to noise ratio (A weighted)    105dBA (Analog Input) 112dBA (Digital Input)
THD+N (@ 1Vrms out, @ 1Khz)    <0.005%
Crosstalk (channel separation) @ 1KHz    >95dBA

Input Stage:
Analog low level Inputs    6 ch. (Differential input) (Molex microfit to RCAs)
Analog high level Inputs    6 ch. (Differential input) (Molex microfit to tripped ends) + USS (Universal Speakers Simulator)
Digital inputs    Yes (Coaxial SPDIF; up to 24bit 96KHz) (Molex microfit to RCA)
Input sensitivity (low level)    0.8V – 6V RMS
Input sensitivity (high level)    2.5V – 21V RMS
Analog inputs management    Audio input routing matrix type
Analog inputs eq    7 bands paragraphic for each input channel
ART    Automatic Remote Turn-On/Off with Speaker-In

Digital Signal Processor:
Sample rate    96KHz
Bit depth    24
Output equalizer    15 bands per channel w/ adjustable Q and Frequency
Equalizer resolution    1/10th dB per step +12dB / -12dB
Time alignment (distance)    0 ÷ 468.4 cm / 0 ÷ 184.4 inches
Time alignment (time)    0 ÷ 13.5ms
Time alignment (step)    0,08 ms; 2,8 cm / 1.1 inch
Time alignment (fine set)    0,02 ms; 0,7 cm / 0.27 inch
Crossovers    AP/HP/LP/BP all channels
Crossover type    Butterworth, Linkwitz-Riley, Bessel (All Channels)
Crossover slope    From 6dB/oct. until 30dB/oct. (6dB step)
Crossover steps    120 steps 20Hz-20KHz
Mute function    Each channel individually, or all channels.
Presets    4 presets
Presets selection    2 specific wires to control the 4 presets selection by extarnal switches.
Input selection by wire    One specific wire to select the desired input between Analog or Digital.
Audio signal compressor on output stage    Yes (enable/disable)
DSP chipset    Analog Device: ADAU1451
DSP management by bt app (iOS/ Android) :  

1. CONFIGURATOR mode Mainly it’ll allow the DSP tuning. You can manage every DSP functon through your smartphone/ tablet/PC/MAC.

2. DRC mode The BT device becomes a remote control by using the dedicated app with a simple graphical user interface. Manage volume level, SUB level, select different setup files, upload a new setup file.
Setup file sharing via bt    Upload a setup file via BT through the BT APP when in “Configurator” or “DRC” mode.
DSP management by pc / mac / ios / android    Microsoft Windows (32/64 bit): Windows 10 (USB and BT BLE) Windows 11 (USB and BT BLE) Mac Os: 10.13 Hight Sierra or later (USB and BT BLE)

Physical Specs:
Max size W x H x D (mm/inch)    130 x 33.8 x 88,3 / 5.11 x 1.44 x 3.47
Weight (kg/lbs)    0,66 / 1.45

Are you looking to add 6x9's to your stock lids? Don't want to spend the big bucks and buy color matched CVO lids from the dealer? Yet you don't want to chinch out and buy crummy aftermarket lids. The Hertz HD14H saddle bag lid cut-in kit makes it possible for you to add their 6x9 speakers to your stock, non-speaker lids you currently have without sacrificing quality, safety and without emptying your wallet.

Will only work on stock, non-CVO lids, without electric lid lock motor, on 2014+ lids.

DON’T SETTLE FOR 5X7S WHEN YOU CAN HAVE 6X9S IN YOUR FACTORY HARLEY SPEAKER LIDS!

This kit requires modification of your factory speaker lids. The integrated plastic basket on the underside of the speaker lid must be cut off and ground down to create a flat mounting surface for the adapter to mount on. This is done quickly and easily with an oscillating cutting tool, or a Roloc disc on a die grinder.

This kit includes (8) eight aluminum threaded nutserts. A nutsert tool with an 8-32 insert is required to complete the installation. If you do not have a nutsert tool, one can be found locally, check with your nearest Hardware store or tool company.