Velocity CoaxHorn System for 2014-2024 Tri Glide

The Velocity RZ65H speakers are a huge jump forward in tunability for pro-audio-type speakers on Harley baggers. We built the RZ65H speakers to sound better out of the box without the typical response issues of horn-loaded pro-audio-type speakers.

These speakers are the best of both worlds
Ultra-high output, and smooth frequency response. Very high efficiency means that you get more output for every watt. 

This is the best-sounding and loudest Harley 6.5" speaker that you will find. The R65 Neo has not been adapted for Harley use, it was designed from the ground up for Harley use. Every part of these speakers has been optimized for performance in the Harley environment.

FEATURES

EXTREME OUTPUT & THE BEST SOUND QUALITY

The Velocity R65 Neo is the 6.5" woofer used in all Velocity OverDrive 6.5" component speaker systems because it is the only speaker in existence that can meet the challenge. This woofer uses a very strong Neodymium magnet that is 10 times as strong as an iron magnet. The R65 is designed to play lower in frequency than other pro audio 6.5" speakers typically do. This makes these speakers more aggressive sounding on their own or when they are paired with other speakers on the bike. The R65 Neo also has an unusually smooth upper-frequency response that allows these woofers to blend nicely with any tweeter that will play down to 5khz (most all do). If you are looking for a very sweet yet aggressive-sounding speaker that can easily handle anything you throw at it, the R65 Neo is a perfect choice.

EASY INSTALLATION

The R65 Neo has been designed specifically for Harley Davidson Baggers and will drop right into all 2014 and newer fairing speaker pods including Road Glide upper fairing, lower fairings (including liquid cooled), as well as Street Glides.

OUR FAVORITE 4 CHANNEL AMPLIFER

The RZA1000.4 is the very best-sounding amplifier made specifically for Harley use. This amplifier has better speaker cone control at high volumes for better bass, and far better high frequency fidelity than other amplifiers. Natively compatible with factory Harley radios and aftermarket radios alike, the RZA1000.4 has a super wide range input (.41 to 10 volts) that is balanced so that it can accept anything from a standard line level RCA to a high voltage speaker level input directly from a factory radio. And it does this without the need for any noisy line levelers. This amplifier uses a far superior internal power supply to other amplifiers and can sustain extreme performance where other amplifiers just run out of gas and clip or drop in volume. This is a beast of an amplifier in a small footprint. This amplifier features a full chassis heat sink for more performance in a much smaller size package. The full chassis heat sink also allows for the amplifier to be mounted in any position and to keep cool even on the hottest summer days.

FEATURES:
Full Chassis Heat Sink Design Can Be Mounted in Any Position

• Compact Design Fits All ‘14 and Later Fairings Without Any Modification
• Super Wide Range Signal Input Stage Is Compatible With Most Any Type of Analog Signal
• Made Specifically for Harley Applications
• Optimized for Velocity Speakers
• Flexible Design Is Perfect for Every Type of Speaker on a Bike Including Subwoofers, Bag Woofers, Mid Ranges, and Tweeters
• Onboard Active 12 db crossovers

Specifications:

• 1,350 Watts Peak Power

• 4 x 275 Watts @ 2 Ohm RMS

• 4 x 150 Watts @ 4 Ohm RMS

• 2 x 550 Watts @ 4 Ohm RMS

• Frequency Response 20hz - 25khz

• Crossover High/Low Pass 40hz - 400hz @ 12db

• Signal Input Range .41V - 10V Balanced High & Low Level

• RCA Input - Yes

• Speaker Level Input - Yes (over RCA connection)

• Efficiency 87% @ Full Power

• Remote Trigger 12V or Signal Sense

This Is The Part You Need! Adding An Amplifier To Your 2014 Or Newer Harley Davidson Touring Bike Has Never Been Easier.

True Plug & Play! This is the very best way to integrate an aftermarket amplifier with the factory radio of any '14 or newer Harley bagger. This harness gives you all of the connections and features you could want and it works with all variations of Harley stereo systems from basic to CVO Ultra models, both factory-amplified and non-amplified.

This Part Replaces All of the Following Harnesses. Which makes it the best deal, and the cleanest and easiest way to go:

• 2014-Up Harley Plug & Play Signal Adapter 14FPNP
• 2014-Up Harley Plug & Play Rear Signal Adapter
• Stealth Accessory Harness Power Tap
• Rear Harley Speaker Wire Harness for Bags or Tour Pack
• Stealth Power Tap Harness for Battery & Ground
• Ultra Rear Radio Signal & Speaker T Harness
• Harley Speaker Pod Plug Adapters for Fairing Speakers

Fitment: 2014 and up Road Glide, Street Glide, Electra Glide, Ultra, CVO, and all amplified and non amplified variations. Amplifier bypass plugs required for all factory amplified systems.?Amplifier bypass plugs are available. Balanced speaker level on RCA, requires an amplifier or DSP that is designed to accept speaker level in on RCA connection (most all quality amplifiers and DSPs do accept speaker level, but check your equipment to make sure). CVO and bikes that only have fairing speakers will require a radio flash to enable the rear RCA output. You can flash your own bike with a separate single bike flash tool.

Does Not Work With Sound Digital Or Dayton Amplifiers (there may be others we're not aware of though)

• True Plug & Play! No cutting any factory wires.
• Both front and rear (4 Channel) RCA out from factory radio (balanced speaker level on RCA, requires an amplifier or DSP that is designed to accept speaker level input on RCA connection).
• Front and rear speaker connections for factory locations.
• Built-in load resistors keep factory radio happy and eliminate distortion.
• Accessory, battery, and ground outputs for powering DSP without the need for any additional parts or plugs.
• Wire ferrules and crimp connectors built into the harness. No extra connectors needed.
• 100% developed and designed by American Hard Bag in the USA.

This power amplifier kit comes complete with all the cabling, speaker wires, terminals, disconnects, and waterproof fuse holder needed to perform a quality installation for a typical amplifier, except for RCA interconnects.

What We Like About This Kit:
It has a waterproof eight gauge fuse holder that uses mini ANL-style fuses for superior current transfer and reliability. Furthermore, the fuse holder is compact and very friendly to mount. All of the wire runs are blacked-out with a nice-looking braided loom and heat-shrunk at each end.

S8 DSP

The ultra-compact S8 DSP is the perfect solution for integrating any OEM source into your audio upgrade project for cars, motorcycles, and boats! S8 DSP is a distilled essence of technology at the service of the highest audio quality in a corrosion-free case cast in metal and composite materials.

S8 DSP processes the audio signal with 96 kHz / 24-bit resolution and has obtained the Hi-Res certification from the JAS (Japan Audio Society), an acknowledgment that certifies the extreme level of audio performance achieved.

The powerful 32-bit DSP manages 6 high/low-level analog input channels, one digital coaxial input, and 8 output channels, offering maximum freedom of configuration to the specialist. The SPDIF coaxial input is ideal for digital connection with a Hi-Res player, a solution that allows for maximum listening quality. For each of the eight output channels we have a level control, the 15-pole parametric equalizer, time delays, and crossover filter available. The 7-band parametric equalizer of the input signal allows obtaining a flat response from OEM sources, which often have an exaggerated emphasis on the low frequency.