Installing American Hard Bag Harley Saddlebag Amplifier Wire Harness
This article covers installation of several variations of saddlebag amplifier wire harnesses that we offer including some add on options. The wire harness that you receive may or may not have all of the harness parts described here. The harness that you have may or may not look exactly like the parts pictured here. Saddlebag wire harnesses can be used in either the left or right side bag. All variations of these harnesses allow you to install an amplifier in one saddlebag and drive speakers that are located outside of that saddlebag in other locations on the bike. This harness provides quick disconnects for all amplifier circuits and all connections are designed for water exposure, heat, and extreme vibration. These connections include power, ground, remote turn on, RCA, and speaker outputs.
Below you will find pictures and descriptions of the major components of this kit.
Bag Side Main Harness (Pic 1) |
|
Bag Side Main Harness (Pic 2) |
|
This harness is 6 ft long, which may seem excessive, but it is actually the perfect length for lid speakers. Read more about that in the installation details below. Connect this harness to the speaker in the bag without an amplifier. If using on woofers down low in the bag you can trim this cable down to whatever length you need.
Speaker Input Harness for Second Bag (Pic 3) |
Bike Side Power Harness (Pic 4) |
Bag Side Power Harness (Pic 5) |
Notice that in the pic above the bags on the right have been taped to protect the paint and the bags have been clamped to the bench with a soft cloth under them. It is much easier to work on a bag that is clamped to the bench.
![]() |
This way the bag stays still as you work. Overview Diagram Note: Though this diagram shows the amplifier in the right side bag, this kit will work equally as well with the amplifier in either the left or right side bag. This harness even works for installing the amplifier in a tour pack. |
Installation Step 1
Identify the main harness and the direction that all circuits will run on the bike (RCAs, turn-on, and speaker circuits). The main harness is made up of two distinct parts that contain remote turn-on, RCA and speaker circuits. Some custom harnesses will not have RCAs integrated into the main harness. We make them both ways.
- The bike side harness. You can easily identify this part (see pic 1 above). The large multi pin connector has female pins as well as a two pin female connector for the second bag speaker. This harness runs from the side cover area in front of the bag in which you are installing the amplifier, up to the fairing as well as the second bag that does not contain the amplifier.
- The bag side harness. You can easily identify this part (see pic 2 above). This side of the harness does not have a two pin connector for the second bag speaker. There is only one black multi pin connector on this harness and it has male pins. This harness runs from the side cover area where it connects to the bike side main harness, to the amplifier inside the bag. This harness contains all speaker connection circuits except any speakers that are in the same bag as the amplifier. Those speaker connections are made in the bag using the “extra speaker wire” that comes in your kit. No external disconnect is required for speakers that reside in the same bag as the amplifier. FOR EXAMPLE: A 4 channel harness will have three external speaker wire circuits. Two fairing speakers and one speaker wire run to the second bag that does not contain the amplifier.
Lay the Harness Out On the Bike.
Plug both the bike side and bag sides of the main harness together. Position the large black multi pin connectors under the side cover in front of the bag with the amp, in an area where it will be easily serviceable and will not interfere with any moving components of the bike. 4 channel kits will have a 4 conductor speaker wire run for the front fairing speakers. 2 channel kits will not have front speaker circuits. Route the fairing speaker wire cable, RCAs, and remote turn-on cables to the front of the bike.
Step 2
Route the cable with the 2 pin black plug (#2 in pic 1 above) to the opposite side of the bike and locate it in the side cover area in front of the bag without the amplifier. This is the connection for speakers in the second bag with no amp. The best way to do this is to remove the battery from the bike and route the cable either in front of or behind the battery. Do not route this cable over the top of the bikes frame. Unbolt the bike's fuse holder assembly on the clutch side of the bike.
This whole assembly can be unbolted by removing the two torx bolts. Once unbolted the assembly will still be connected to the bike by the wire harness. If you need more room to work you can cut the large zip tie that holds the main harness to the backside of the assembly. Be sure that you replace this zip tie when reassembling.



![]() |
|

Step 4
Mount the fuse holder and make your battery connections. American Hard Bag saddlebag amplifier wire harnesses have a dedicated power harness section. This is a two piece harness that has a bike side (part 1) and a bag side (part 2). The bike side connects to the battery and provides a quick release power connector at the side cover in front of the saddlebag. The fuse holder should be located either in front of the battery or under one of the side covers under the seat. We always prefer that the fuse holder is zip tied under one of the side covers. The side cover location is an easily accessible and logical location for a fuse holder since that's where the factory Harley fuse boxes are.
-
Check the fuse holder and remove the fuse (if it has one in it) before installation.
-
Find a safe location for the fuse holder and zip tie it in place where it will not short out to a grounded surface, where it is easily accessible, and where the power leads will not become twisted, cut, or damaged.
-
Locate the power connector in the side cover area where the bag side of the harness can reach. Don’t leave too much slack or the side cover may be difficult to put back in place. Once situated, use a zip tie to tether the power input and output cables to a solid structure such as the frame or the factory fuse box structure.
-
Temporarily connect the bag side of the power harness to the bike side of the power harness so that you can be sure that the entire assembly fits and is well situated in the side cover area.
-
The ideal cable length from the wire exit point of the bag and the connectors is about 14 inches.
There is a lot of room for connections under and in front of the ABS module on the throttle side of the bike. Be sure to adjust the length of all cables so that the connectors all fit comfortably. If you leave the cables too long they will be difficult to put in place and get the side cover back on when you are done. If you have them too short you will not be able to make the connections. Take your time here. When done correctly the connections will be easily serviceable and the side cover will go back in place without any difficulty. Notice that the saddlebag cables run on the outside of the frame. There is plenty of room between the side cover and the frame for the cables.
Tips & Details
Speaker Cable & Connections
Red = Positive
Black = Negative
White = Left positive
Green = Left Negative
The speaker cable is a high quality oxygen free copper cable that has been designed to be very compact and friendly to run throughout the bike. The outer casing of these cables are made of a durable plastic that is friendly to strip and taylor to your particular installation. To strip the casing off, score the casing around the outside where you want to strip it down to. Then bend the cable and the casing will easily snap where it was scored. The cable has a nylon ripcord embedded into it that can be pulled on to split the casing away for you. Score and break off a small section of the casing near the end of the cable. This will expose the ends of the individual wires as well as a section of the ripcord. Use pliers to grab the ripcord and shear off the casing as needed.
The individual speaker wire conductors within this cable have a high grade thin walled PVC insulator that is designed to be a premium covering yet not add much to the diameter of the cable. The copper of these cables are 100% OFC, which is the very best for speaker cables. The end result is a whole lot of quality speaker cable in a very compact package.
Tip: The outer black casing of these cables is intentionally rigid. This makes the cables a lot nicer to route through the bike. You can heat the casing with a heat gun if you want to straighten a bent or twisted cable or if you want to custom shape a cable. A good example of when you would want to do this is when routing our speaker cables along the inside of the saddlebag.
Connecting to Lid Speakers
When routing speaker, power, and RCA cables in a saddle bag the cables can be routed in a way that keeps them out of sight and out of harm’s way. In the pic below the saddlebag has 8 gauge power and ground, remote turn on, two subwoofer connections in the bag, one subwoofer connection exiting the bag, two speaker runs to the lid, and LED lighting for the subwoofers as well as the lid speakers. Most of the wiring is concealed under the two subwoofers and tucked between the amplifier and the inner wall of the bag. All of the amplifier connections enter the bag just forward of the shock tower and then take an immediate 90 degree turn towards the rear of the bag. Under the second subwoofer (rear) the cables make a 180 degree turn and loop back up to the amplifier at the front of the bag. This loop in the cables makes it possible to easily service the amplifier and get to all of the connections.
![]() |
![]() |
Above you can see the route for the lid speaker wire.

For additional questions and installation advice feel free to give us a call 1(888) 311-0016